Question: What do these codes on my bounce report mean?
Product Family: Act!
Product: Act! Marketing Automation
There is not a set list of reasons for each bounce code or message. This is due to the code and reason being set on the receiving server, not on the Swiftpage server, i.e. each server that receives an email that bounces will send its own bounce code which may differ from other servers.
Most codes do have a common reason, so the below tables can be used. However, please note that the tables below are not all encompassing and are meant as a general guide.
There are two types of bounce codes, traditional codes which are 3 digits with no separation, and enhanced codes which are 3 digits separated by a period.
|000||Domain name does not exist|
|421||Service not available, closing transmission channel|
|450||Requested mail action not taken: mailbox unavailable (e.g., mailbox busy)|
|451||Requested action aborted: error in processing (e.g., unable to reach destination system, bad email address, includes unspecified reasons as well)|
|452||Requested action not taken: insufficient system storage|
|500||Syntax error, command unrecognized|
|501||Syntax error in parameters or arguments (e.g., invalid sending email address, invalid recipient address)|
|502||Command not implemented|
|503||Bad sequence of commands|
|504||Command parameter not implemented|
|550||Requested action not taken: mailbox unavailable (e.g., mailbox not found, no access, or command rejected for policy reasons)|
|551||User not local; please try|
|552||Requested mail action aborted: exceeded storage allocation|
|553||Requested action not taken: mailbox name not allowed (e.g., mailbox syntax incorrect)|
Mail admins may modify messages sent with the codes which may give more information than the above from their server; Information from RFC2821 http://www.rfc-editor.org/rfc/rfc2821.txt
Enhanced codes will typically begin with a 2, 4 or 5. This first digit indicates the following:
4.X.X Persistent Transient Failure
5.X.X Permanent Failure
The codes shown below are most commonly seen beginning with 5.
|5.0.0||Email address does not exist|
|5.1.0||Other address status|
|5.1.1||Bad destination mailbox address|
|5.1.2||Bad destination system address|
|5.1.3||Bad destination mailbox address syntax|
|5.1.4||Destination mailbox address ambiguous|
|5.1.5||Destination mailbox address valid|
|5.1.6||Mailbox has moved|
|5.1.7||Bad sender's mailbox address syntax|
|5.1.8||Bad sender's system address|
|5.2.0||Other or undefined mailbox status|
|5.2.1||Mailbox disabled, not accepting messages|
|5.2.3||Message length exceeds administrative limit.|
|5.2.4||Mailing list expansion problem|
|5.3.0||Other or undefined mail system status|
|5.3.1||Mail system full|
|5.3.2||System not accepting network messages|
|5.3.3||System not capable of selected features|
|5.3.4||Message too big for system|
|5.4.0||Other or undefined network or routing status|
|5.4.1||No answer from host|
|5.4.3||Routing server failure|
|5.4.4||Unable to route|
|5.4.6||Routing loop detected|
|5.4.7||Delivery time expired|
|5.5.0||Other or undefined protocol status|
|5.5.3||Too many recipients|
|5.5.4||Invalid command arguments|
|5.5.5||Wrong protocol version|
|5.6.0||Other or undefined media error|
|5.6.1||Media not supported|
|5.6.2||Conversion required and prohibited|
|5.6.3||Conversion required but not supported|
|5.6.4||Conversion with loss performed|
|5.7.0||Other or undefined security status|
|5.7.1||Delivery not authorized, message refused|
|5.7.2||Mailing list expansion prohibited|
|5.7.3||Security conversion required but not possible|
|5.7.4||Security features not supported|
|5.7.6||Cryptographic algorithm not supported|
|5.7.7||Message integrity failure|
Mail admins may modify messages sent with the codes which may give more information than the above from their server; Information from RFC3463 http://www.rfc-editor.org/rfc/rfc3463.txt
Hard vs Soft Bounces
When an email sent from one of your Act! Marketing Automation campaigns bounces, it can be classes as a soft or a hard bounce. This will affect how AMA handles the bounce:
‘Soft’ bounces are where an email couldn’t be delivered to an email address for temporary reasons. The email address sent to is valid and the mail server was reached but the email couldn’t be delivered, for example because the recipient’s inbox was full or the email was too large.
‘Hard’ Bounces are where an email couldn’t be delivered to an email address for permanent reasons. There can be a number of reasons for this but examples of the more common ones are that the email domain doesn’t exist or the email address doesn’t exist.
Hard bounces and Admin bounces are fed back to our servers and flagged so that emails are prevented from being sent to these email addresses. Hard bounces CANNOT be removed from your suppression list manually, instead it would require a call to the Act! technical support team (see the articles linked below for more information). This can only be done on an ad-hoc basis, we cannot remove hard bounces in bulk in order to protect our own sender reputation.
For information on managing your bounces please refer to: